Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Don't undervalue the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several accidents entailing forklifts.

Instance 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the motorist is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backward. .
2. Do not raise the fork expensive when driving. When entering and leaving the work website or while driving, beware that there will certainly be no obstacles in the sky. When the load is traveling, the fork has to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular security range from the vehicle ahead. .
7. When the forklift is running, the load must be in the lowest position that does not impede the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when stacking or packing. .
8. The height of the load must not block the driver's view. In unique conditions, when the thing impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive safely at a low speed when going into the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is forbidden for workers to stand on the fork to hold products and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt manner, and they will never ever run with illnesses or hide them.

filling and discharging.
1. When fork-loading items, the range in between the two forks must be readjusted as needed to make the lots of the two forks balanced and not skewed, and one side of the thing should protest the rack. .
2. It is forbidden to collaborate with a single fork or use a fork top or pull. In unique circumstances, safety and security indication need to be established to advise surrounding pedestrians. .
3. In the process of loading and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be sluggish and stable. Be careful not to roll the wheels Stand-on Electric Pallet Stacker on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it ought to be kept in mind that the fork idea should not touch various other items or items. The load must be supported with marginal back tilt of the gantry to ensure that the lots does not slide backwards. The pole Electric Forklift Truck for Warehouse can be tilted ahead a little when the load is reduced to permit simple positioning of the tons and removal of the forks. .
6. It is forbidden to fork products at high speed and collide with tough objects with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to loaf the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Straining is prohibited, and it is restricted to make use of forks to raise employees to engage in high-altitude procedures to prevent high-altitude falling accidents. .
9. It is not allowed to use the brake inertia to slide, place, round or roll objects. .
10. It is not permitted to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Pull the emergency brake take care of to dead or depress the hand brake switch.
3. The engine is shut off and the power is cut off. (Except for unique conditions, such as the chauffeur does not leave the car's line of sight and does not surpass 1 min).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look should be checked, and gas, lubing oil and air conditioning water need to be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the stress and temperature level are regular.
5. After the forklift is running, the external leak needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine prior to leaving the car;.
2. When you run into somebody before you throughout driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " cost-free switching";.
6. Adding and down the slope must be slow-moving and uniform, and no turning on the incline is permitted.
7. Do not drive across the gradient. When the slope is above 10%, the automobile needs to be driven backwards when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and most likely to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" ought to be followed in the operation.
1. Solitary fork procedure is not allowed.
2. It is not allowed to raise the goods for far away driving.
3. It is not permitted to grab the goods by handing over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll things.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844